Residential Garage Door Services
New Garage Door Installation
Customers can choose what type of garage door repair from numerous companies provide services such as Amarr and Clopay.
Garage Door Opener
Customers can choose from broken springs such as Chamberlain and LiftMaster. Belt drive or chain drive options are available as well. We also offer garage door openers that can be controlled and monitored by your secured smartphone device.
Repairs & Maintenance
We repair and service garage door problems such as broken springs, rollers and tracks, broken brackets/hinges, off-track doors, opener/motor issues, remote and keypad programming, and more.
Frequently Asked Questions
- Locate the “Learn” button on the back of the motor unit, or on the inside wall control. The “Learn” button on the motor unit will usually be purple, red-orange, green, or yellow. On wall-mounted jackshaft openers, lift up the access door on the motor to find the “Learn” button. NOTE: Most newer operators after 2012 have a “Learn” button on the inside wall control, maybe under the flip-up cover. On LCD wall controls models, you have to go in the Menu features to find the “program remote” feature.
- Press the “Learn” button momentarily. If the “Learn” button is on the wall control, you will have to press this “Learn” button TWICE. When the unit is in “Learn” mode, the small LED light next to the button will be solidly lit.
- Within 30 seconds, press and hold the remote button for a couple seconds. This will program that button into that motor. The next push of the remote button will operate the door.
- Repeat the steps above for any additional remotes for that door.
- If the remote has multiple buttons, the other buttons can be programmed to other door motors using the same procedure.
- If you still need a garage door repair, please feel free to call Garage Door Repair Maryland at (301)-200-1217.
- Locate the “Learn” button on the back of the motor unit, or on the inside wall control. The “Learn” button on the motor unit will usually be purple, red-orange, green, or yellow. On wall-mounted jackshaft openers, lift up the access door on the motor to find the “Learn” button. NOTE: Most newer operators after 2012 have a “Learn” button on the inside wall control, maybe under the flip-up cover. On LCD wall controls models, you have to go in the Menu features to find the “program remote” feature.
- Press the “Learn” button momentarily. If the “Learn” button is on the wall control, you will have to press this “Learn” button TWICE. When the unit is in “Learn” mode, the small LED light next to the button will be solidly lit.
- Within 30 seconds, press a 4-digit number into the keypad and then immediately press and hold the “Enter” button for a couple seconds. This programs the new 4-digit code to that motor and erases any previously programmed code for that door.
- A different 4-digit code can be used to program other door motors by following the same procedure. One keypad can operate multiple doors.
- If you still need a garage door repair, please feel free to call Garage Door Repair Maryland at (301)-200-1217.
- Press and hold the “Learn” button for about 8 seconds until the LED light next to the button goes off. All remotes and keypads will be erased on that motor.
- Reprogram devices per above instructions.
- If you still need a garage door repair, please feel free to call Garage Door Repair Maryland at (301)-200-1217.
- If multiple doors/motors are programmed with a keypad (a different 4-digit code must be used for each door), one press of the “Enter” button on the keypad will close all open doors.
- If the door reverses when going down, it is most likely the safety eye sensors at the bottom of the door. Make sure they are clean and pointed at each other, no objects are blocking them, and all the wires are connected.
- Whenever a remote button or keypad “Enter” button is pressed, the device is sending out the radio signal. Holding the remote or “Enter” button down for a few seconds will increase the range and effectiveness of the signal.
- The keypad “Enter” button may have to be pressed twice sometimes to send out a good signal.
- Changing batteries will not erase the programmed codes.
- Clean the battery terminals with a pencil eraser or file when changing batteries.
- If you still need a garage door repair, please feel free to call Garage Door Repair Maryland at (301)-200-1217.